Carving Ham

Carving

Whole Ham | Spiral Sliced Ham | Shank Half Ham | Butt Half Ham

The whole ham, half ham, or ham portion will need to be carved into smaller pieces for serving. Before carving, the meat should set for 10 to 15 minutes after it is removed from the heat source. This allows the juices to be redistributed throughout the meat, resulting in a firmer, juicier and easier to carve ham. A country ham will carve easier if it is at room temperature or cooler. Choose a carving knife that is long enough to cut the entire length of the cut. It is important that the knife be extremely sharp so that it will allow thin slices to be carved and make carving easier. Shown below are the steps to carving different ham cuts

Ham Carving - Whole Ham:

Place the ham on a cutting board and trim off 2 or 3 slices, parallel to its length, from the thin side of the ham. Turn the ham so that it rests on the flat side created from trimming off the slices.
Hold firmly with a carving fork and starting at the shank end, cut slices across the ham, down to the bone.
After cutting the slices, cut parallel along the bone to release the slices. Place slices on a serving platter.   Turn the ham and continue to carve slices in the same manner.

Ham Carving - Spiral Sliced Ham:

Special spiral sliced hams provide slices that are uniform in thickness. Three basic cuts are generally all that are required to cut the slices from the bone.

Facing the cut side of the ham, locate the natural muscle lines in the ham. Cut along the first line down almost to the bone. Cut around the bone until the natural muscle line starts to curve upwards. Continue to follow the line all the way up until the knife comes back out the outside edge. This will provide the first section of slices.

Continue to cut along the next natural muscle line to provide the next section of slices.

The remaining section will need to be cut along the bone to release it, providing the last section of slices.

The three sliced sections can then be cut into smaller serving sizes if desired.

Ham Carving - Shank Half

	Place the ham on a cutting board and trim off 2 or 3 thin slices from one side of the ham. Turn the ham so that it rests on the flattened side created from trimming off the slices. This allows the ham to sit more steady while carving.
	Starting at the narrow end of the ham, begin making 1/4 inch slices (or desired thickness) in the ham. Slicing down to the bone.

After all slices are cut on the first side, place the ham on its flat end. Trim slices off by cutting down through the ham, close to the bone.

After cutting down through all the slices, place them neatly on a serving platter.

Flatten one of the remaining uncut sides of the ham by cutting 2 or 3 thin slices off. Stand the ham up on the flattened side and start slicing the uncut side, beginning at the narrow end of the ham.
Set the ham on its flat end and trim down close to the bone to release the slices from the ham. Place slices neatly on the platter with the other ham slices. Continue to trim the two remaining sides of the ham in the same manner.

Ham Carving - Butt Half

	Lay the flat end of the ham on the cutting board. Cut down through the ham as close to the bone as possible, cutting off the largest section of boneless meat from the ham. Set the boneless section aside to be sliced after slicing the remaining section of the ham.
With the flat end still on the cutting board, cut 1/4 inch slices (or desired thickness) parallel to the flat end of the ham by making horizontal cuts. Starting at the top, cut slices off until you reach the bone area.
	Then cut slices horizontally to the bone in the center. Continue making horizontal slices until all slices are cut. Release the slices from the ham by cutting down through the ham, close to the bone. Place the slices neatly on a platter. Slice the other side of the remaining ham in the same manner.
	After cutting the slices from the bone-in section of the butt ham, place the boneless section with the side that was just cut down on the cuttng board. Slice the boneless section into the desired thickness. The slices from this section may be fairly large so you may want to cut them in half to produce smaller slices for serving.